Have any questions? Please give us a call at 520-625-5511
Terms of Use | Privacy Policy
Install a flagpole in your yard to display your pride for your country, state, teams, or other causes.
Match the letters in the photo to the corresponding parts in the article.
Install a flagpole in your yard to display your pride for your country, state, teams, or other causes.
Want to let your true colors fly? Whether is the American flag, Arizona flag, your favorite sports teams (the Saints & LSU), or welcoming a new season, hoisting your flag high in the air lets everyone around know you are proud of where you come from and what you support.
With the help of our friends at This Old House, we will take you through the steps to select and install an in-ground flagpole.
The Anatomy of a Flagpole
There are many components to a flagpole. Knowing what they are will make installation much easier. Carrot-Top Industries explains them below.
Match the letters in the photo to the corresponding parts in the article.
A | Finial — A decorative ornament that’s mounted at the top of the flagpole, above the truck. Typically, a finial might be in the shape of an acorn, a ball, or an eagle.
B |Truck — Pulley assembly that mounts at the top of the flagpole. Stationary trucks are mounted over the top of the flagpole and are secured with setscrews, while revolving trucks screw into the flagpole’s top with a standard 1 ¼” National Pipe Thread spindle. Revolving trucks are mounted with bearings that allow them to turn along with prevailing winds.
C | Snaphook — Also referred to as a flag snap, the snaphook is a metal or vinyl hook with a spring closure, used to attach the flag to the halyard. Snaphooks are similar to the type of closure often found on a dog’s leash.
D |Halyard Channel — Usually several feet long, the halyard channel extends upward from the cleat, covering the external halyard and helping protect against theft or vandalism.
E | Halyard — The halyard is the rope that is used to raise or lower the flag and can be located internally or on the outside of the pole. The halyard runs through the pulley system in the flagpole’s truck and is secured with the cleat at the base of the pole.
F | Cleat — A T-shaped metal device that holds the hoisted flag in place by wrapping the halyard around the cleat multiple times. The cleat is typically mounted to the pole about five feet above ground level.
G |Butt — The flagpole’s base end; the larger, lower end of the flagpole shaft.
H |Flash Collar — A cover that goes around the base of the pole at ground level, usually the same color and material as the flagpole. A flash collar gives the pole a clean, finished look and helps protect the flagpole and foundation from the elements.
I |Foundation Tube — A steel or PVC tube that is placed in the ground to support and hold the shaft securely in place.
Now that you know the terminology, it’s time to decide where the pole will be placed. Assemble a mock-up with PVC pipe and couplers. Have someone hold up the pole in various spots so you can judge the effect from afar. Consider the height of the house or building when selecting the pole’s height: 18 to 25 feet for a single-story building, 25 to 30 feet for two stories, and 30 to 40 feet for three stories.
You may find it helpful read the laws about flying the American flag. You can review the “Conduct during hoisting, lowering or passing of flag” in Section 9 of the Flag Code.
There are several types of poles to consider.
Wood: Historically authentic and the most expensive option. Like the wood on the exterior of your house, it must withstand the elements for a long time, and therefore requires regular maintenance.
Standard Aluminum: Although light, easy to install, and available with internal rigging — no halyards to clang against metal. Note that some painted aluminum poles chip, leaving uncoated spots that may stain. Select a durable finish with a clear-coated brushed metal, which often looks incongruous against a white clapboard house.
Fiberglass: Look for one with a UV-resistant finish and constructed with the majority of fibers running vertically. Horizontal fibers are not as strong and can cause failure. Fiberglass poles are available in various colors and are light, easy to install, and maintenance-free. The rigging can be run inside the pole to eliminate the sound of slapping halyards. Lowering the flag takes a little work.
Telescoping Aluminum: The model has retracting buttons and joints and is easily portable. Putting them up and taking them down takes just a few minutes.
You will need these tools and materials for proper installation.
1 | Dig a Foundation for the Anchor
• The day before installation, dig a foundation hole 30 inches deep and 24 inches in diameter, using a post-hole digger and shovel. This will hold the painted steel anchor, which supports the pole and prevents ground moisture from wicking up and rotting the wood.
• For soil that doesn't drain well, add 6 inches of gravel or crushed rock to the bottom of the hole you dug.
• Following the instructions on the bag, mix a batch of Redi-Mix cement. It will take several bags. Fill in around the base of the pole (roughly 6 inches of concrete). Let it set per the mix's instructions, then drop in the anchor.
• Allow the concrete to set at least two days (one week is better) before using the pole.
• Check the anchor's alignment using an 18-inch bubble level or laser level, then fill the hole with concrete and trowel it smooth.
2 | Drill Holes for the Pivot Bolt
• After the concrete has set for 24 hours, rest the pole on two padded sawhorses.
• Center the cleat on the pole's halyard side by measuring 42 inches from the bottom.
• Using an 11/16-inch bit, drill holes for two ⅝-inch bolts.
• To affix the truck (the flanged top that holds the finial and through which the halyards are threaded), set the double sheave into a notch on the top of the pole, so a sheave with the halyard pulled through lines up with a cleat on the base.
• Before screwing the truck on, coat the inside and edges with silicone caulking for a watertight seal.
• Fit the finial into a ½-inch threaded hole in the center of the truck.
• Set the pole into the anchor and insert the pivot bolt. Adjust the pole until it is plumb, checking how it looks from afar as a helper holds it steady.
• Holding the preferred position, mark the pole at the predrilled holes on the anchor. Remove the pole, rest it on the padded sawhorses, and drill holes for the locking bolt.
• Insert the pole into the anchor again and install the pivot bolt.
• Finally, install the locking bolt and finger tighten it. Once again, check to make sure the pole is plumb.
If you want your flag to fly from dusk to dawn, per the Flag Code, it must be illuminated. Add a solar light. You won't have to dig a trench for an electric line or deal with expensive outdoor light! Solar light kits for flag poles are available at most flag dealers and online.
After the installation is complete, attach your flag.
When you are ready to buy or replace your American flag, look for the Flag Manufactures of Association of America (FMAA) Certified American Made seal to know you are buying a flag made here in America! The flag we have in our eStore is manufactured by Valley Forge Flag company and carries the Platinum seal.
If a flagpole is not an option, purchase the Stainless Steel Flag Pole Mounting Bracket, also available in our eStore and hoist your flag high to the sky!
For more do-it-yourself tips, go to rosieonthehouse.com. An Arizona home building and remodeling industry expert for 35 years, Rosie Romero is the host of the Rosie on the House radio program from 8 a.m. to 11 a.m. Saturdays on KTAR-FM (92.3) in Phoenix; KGVY (1080AM 100.7FM); 10 a.m. to 11 a.m. in Tucson and KNST-AM (790) in Tucson.
THE EVENTS CALENDAR IS SPONSORED BY:
Subscription services - active digital access, subscribe, missing newspaper, stop/starts etc.
Copyright © 1999- • Green Valley News • 101 S. La Cañada Dr., Ste. 24, Green Valley, AZ 85614 | Terms of Use | Privacy Policy | Contact Us | The GREEN VALLEY NEWS & SUN is owned by Wick Communications.
Get up-to-the-minute news sent straight to your device.
Receive the digital, interactive PDF of the newspaper in your inbox. Delivered right as the newspaper goes to print on Thursdays and Sundays.
Receive the digital, interactive PDF of the newspaper in your inbox. Delivered right as the newspaper goes to print on Sundays.
Your account has been registered, and you are now logged in.
Check your email for details.
Invalid password or account does not exist
Submitting this form below will send a message to your email with a link to change your password.
An email message containing instructions on how to reset your password has been sent to the e-mail address listed on your account.
Your purchase was successful, and you are now logged in.
A receipt was sent to your email.